Length Converter

Convert mm, cm, inches, feet and more instantly.

Inch to mm 1 in = 25.4 mm — fraction chart and inch-to-millimeter pages.

Decimal inches
0.9843
Nearest 1/64
63/64 in

25 mm ÷ 25.4 = 0.98425197 in

Names that are not the measured size

1 inch is exactly 25.4 mm. A 1 1/2 in length is 38.1 mm, and a 2 1/2 in length is 63.5 mm. Pipe, copper tube, and lumber use those fractions as names for different actual sizes. The two pages below work the differences out, including Schedule 40 inside diameters and the nearest metric bolt and drill.

Same fraction, three different diameters. Millimeters are the inch size × 25.4.
What people sayActual sizemm
1 1/2 in length, or a dry 2× board’s thickness1.500 in38.1
NPS 1-1/2 pipe, outside diameter1.900 in48.26
Copper water tube, nominal 1-1/2, outside1.625 in41.275
2 1/2 in length, or a dry 3× board’s thickness2.500 in63.5
NPS 2-1/2 pipe, outside diameter2.875 in73.025
Copper water tube, nominal 2-1/2, outside2.625 in66.675

A dry dressed 2×4 is 38.1 mm by 88.9 mm, not 2 in by 4 in. NPS 1-1/2 pipe is 48.26 mm outside, not 38.1 mm. NPS 2-1/2 pipe is 73.025 mm outside (charts often round that to 73.02 mm), not 63.5 mm. Copper water tube runs 1/8 in over the nominal name: 41.275 mm and 66.675 mm.

FAQ

  • How many millimeters are in an inch?

    One international inch is exactly 25.4 mm. Every result on this site multiplies or divides by that factor. A foot is exactly 304.8 mm (12 × 25.4), and a meter is 1000 mm.

  • Is 1.5 inch the same as 1 1/2 inches?

    Yes. Both are 1.5 × 25.4 = 38.1 mm. The 1 1/2 inches to mm page also compares that length with pipe, a dry 2×4, and the nearest metric drill.

  • Is a 2×4 actually 2 inches by 4 inches?

    No. A dry dressed 2×4 is 1 1/2 in by 3 1/2 in, which is 38.1 mm by 88.9 mm. Green dressed nominal 2 in stock is 1 9/16 in (39.6875 mm).

  • Is 2 1/2 inches the outside of 2 1/2 inch pipe?

    No. 2 1/2 inches as a length is 63.5 mm. Nominal 2-1/2 pipe (NPS) is 2.875 in outside (73.025 mm). The same gap shows up at 1 1/2 in: the length is 38.1 mm, and the pipe outside diameter is 1.900 in (48.26 mm).

  • Why are 63 mm and 64 mm both close to 2 1/2 inches?

    2 1/2 in is 63.5 mm, exactly halfway between 63 mm and 64 mm. Each whole millimeter is 0.5 mm away, so neither one matches a 2 1/2 in shank or wrench opening.

This free length converter covers mm, cm, m, km, inches, feet, yards, and miles — a focused unit converter for length. Pick any pair of units for a live result and formula; inch results also show decimal inches and the nearest 1/64 fraction. For inches to millimeters, start at the inch to mm hub (1 in = 25.4 mm). The two sizes people mix up with pipe and lumber are 1 1/2 inches to mm ( 38.1 mm, including the 1.5 inch search) and 2 1/2 inches to mm (63.5 mm).