1 1/2 inches to mm

Decimal: 1.5 inch

1 1/2 inches (1.5 inch) = 38.1 mm exactly (3.81 cm). The international inch is 25.4 mm, so multiply the inch value by 25.4.

Millimeters
38.1
Decimal inches
1.5000
Nearest 1/64
1 1/2 in (exact on 1/64)

The inches fraction result is rounded to the nearest 1/64 fraction.

1 1/2 inches to mm conversion

1 1/2 inches (1.5 inch) × 25.4 = 38.1 mm. Reverse: 38.1 ÷ 25.4 = 1.5 in.

1 1/2 inches to mm calculator

Use the converter at the top. Type a decimal or a fraction (1/16, 3 1/2). Millimeters update from the same engine as the inch to mm hub (1 in = 25.4 mm).

How to convert 1 1/2 inches to mm

  1. Write the length as a decimal inch if needed: 1 1/2 in = 1.5 in (1.5 inch).
  2. Multiply by 25.4: 1.5 × 25.4 = 38.1 mm.
  3. Optional centimeters: divide millimeters by 10 → 3.81 cm.

Nearest metric size

The nearest metric size is 38 mm, 0.1 mm smaller than 38.1 mm.

38 mm is 0.1 mm smaller than 38.1 mm and 40 mm is 1.9 mm larger. Those are the metric dowel and hole sizes people compare with 1 1/2 in (1.5 in). Neither is exact. A nominal “1 1/2 inch pipe” is a trade size, not a 1.5 in outside diameter.

1 1/2 inches is 38.1 mm, not a whole millimeter. Whole-millimeter neighbors:

  • 38 mm is 0.1 mm smaller than 1 1/2 inches.
  • 39 mm is 0.9 mm larger than 1 1/2 inches.

1-1/2 inch pipe, wrench, and ruler

1 1/2 inches as a length is 38.1 mm (1.5 × 25.4). That is the conversion on this page — a cut, a wrench opening, or a mark on a stick.

A nominal 1-1/2 inch PVC or waste pipe is a trade size (NPS), not an outside diameter of 1.5 in. ASME B36.10M lists the NPS 1-1/2 outside diameter as 1.900 in, which is 48.26 mm — 10.16 mm larger than 38.1 mm. Inside diameter is smaller than that outside diameter and depends on wall schedule. The lumber and drill section below gives the Schedule 40 and Schedule 80 nominal inside diameters. Measure the actual OD or ID, then multiply inches by 25.4.

Comparison diagram: a 38.1 mm bar for 1 1/2 inches as a length or wrench opening, a longer 48.26 mm bar and circle for NPS 1-1/2 pipe outside diameter, and a millimetre ruler with 38.1 mm marked just past 38 mm
1 1/2 in as a length is 38.1 mm; NPS 1-1/2 pipe OD is 1.900 in (48.26 mm). The dashed circle is not the pipe. Diagram by Length Tools, using the same 1 in = 25.4 mm engine as this page.

A 1-1/2 inch wrench opening is the same 38.1 mm as this length. A 38 mm wrench is 0.1 mm smaller; a 40 mm wrench is 1.9 mm larger. Neither metric opening is an exact 1-1/2 in substitute.

On a millimeter ruler, 38.1 mm sits just past the 38 mm tick (38 mm is 0.1 mm short of 1 1/2 in).

Diagram of an inch divided into halves, quarters, eighths, and sixteenths on a measuring-tape style scale
One inch of a tape, with the ½ mark. 1 1/2 in is one full inch plus that half. Diagram by Offnfopt , CC0 1.0 / Wikimedia Commons .

For the 1 in = 25.4 mm definition as a short lesson, see the video on mm to inches — not a pipe-size video. YouTube already occupies two slots on this query; this page keeps the hardware diagram on-page.

Lumber, bolts, and drill bits

1 1/2 inches as a length is 38.1 mm. The pipe outside diameter is a different number: ASME B36.10M NPS 1-1/2 (also called DN 40) is 1.900 in outside, 48.26 mm. DN 40 does not mean the pipe is 40 mm across.

Schedule 40 wall for that pipe is 0.145 in, so the nominal inside diameter is 1.610 in (40.894 mm), 2.794 mm larger than a 1 1/2 in dowel. On those nominal dimensions the dowel passes through Schedule 40 with clearance. Schedule 80 wall is 0.200 in, and 1.900 − 2 × 0.200 = 1.500 in exactly (38.1 mm) — the same as the length, which is a line-to-line fit, not clearance. Mill tolerance can make the real inside smaller.

ASTM B88 copper water tube labeled 1-1/2 in (Types K, L, and M) has an outside diameter of 1.625 in (41.275 mm), 1/8 in larger than a 1 1/2 in length. Inside diameter depends on the type.

Compared with this length

Difference is from 38.1 mm. Positive means larger than a 1 1/2 in length.

ItemActual sizemmDifference (mm)
1 1/2 in length, cut, or wrench opening1.500 in38.10
NPS 1-1/2 pipe, outside diameter1.900 in48.26+10.16
NPS 1-1/2 Schedule 40, nominal inside1.610 in40.894+2.794
NPS 1-1/2 Schedule 80, nominal inside1.500 in38.10
Copper tube, nominal 1-1/2, outside1.625 in41.275+3.175
38 mm drill or dowel38 mm38-0.1
1 7/16 in drill1.4375 in36.5125-1.5875
1 9/16 in drill1.5625 in39.6875+1.5875
40 mm drill40 mm40+1.9
M36 bolt, major diameter (preferred)36 mm36-2.1
M39 bolt, major diameter (second choice)39 mm39+0.9
M42 bolt, major diameter (preferred)42 mm42+3.9

Dry dressed softwood that is actually 1 1/2 in thick

A nominal “2-by” board is not 2 in thick once it is surfaced dry. The thickness is 1 1/2 in (38.1 mm) — the same length this page converts. A 4×4 is 88.9 mm square, not 1 1/2 in and not 4 in. Green dressed nominal 2 in stock is 1 9/16 in (39.6875 mm; PS 20 lists 39.7 mm).

NominalDry dressedmm
2×41 1/2 × 3 1/2 in38.1 × 88.9
2×61 1/2 × 5 1/2 in38.1 × 139.7
2×81 1/2 × 7 1/4 in38.1 × 184.15
2×101 1/2 × 9 1/4 in38.1 × 234.95
2×121 1/2 × 11 1/4 in38.1 × 285.75

Dry dressed sizes are minimums from the American Softwood Lumber Standard (PS 20) at 19% moisture content or less. Inch sizes are the standard of record. Millimeters are those inches × 25.4. PS 20 rounds a few metric equivalents: 7 1/4 in is listed as 184.2 mm (exact 184.15), 9 1/4 in as 235.0 mm (exact 234.95), and 11 1/4 in as 285.8 mm (exact 285.75). Green lumber is larger, and rough lumber is larger still.

A 38 mm hole is 0.1 mm smaller than a 38.1 mm shank, so it is not clearance for a 1 1/2 in pin. 40 mm leaves 1.9 mm. Among ISO 262 first-choice diameters, M36 is 36 mm (2.1 mm smaller) and M42 is 42 mm (3.9 mm larger). M39 is a second-choice diameter at 39 mm, 0.9 mm larger than 38.1 mm, and it is closer than either first-choice size. Major diameter is the thread size, not the wrench size across the flats.

The same kind of name mix-up at the other focus size is on 2 1/2 inches to mm. Both sizes are linked from the Length Tools home page.

Pipe OD and schedule walls: ASME B36.10M (Schedule 40 wall 0.145 in, Schedule 80 wall 0.200 in). Copper OD: ASTM B88. Lumber: PS 20 Table 3 dry dressed minimums. Bolt diameters: ISO metric nominal major diameter.

Nearby inch fractions

Sixteenth-inch steps from the same 1 in = 25.4 mm factor. Linked rows have their own pages. The full fraction table is on inch to mm.

InchesDecimalMillimeters
1 1/4 in1.2531.75 mm
1 5/16 in1.312533.3375 mm
1 3/8 in1.37534.925 mm
1 7/16 in1.437536.5125 mm
1 1/2 in1.538.1 mm
1 9/16 in1.562539.6875 mm
1 5/8 in1.62541.275 mm
1 11/16 in1.687542.8625 mm
1 3/4 in1.7544.45 mm

Other inch fractions to mm

FAQ

  • How many mm is 1 1/2 inches?

    1 1/2 inches is 38.1 mm exactly. 1.5 × 25.4 = 38.1. 38 mm is 0.1 mm shorter than this length.

  • What is 1 1/2 inches in mm?

    1 1/2 inches in mm is 38.1 mm (3.81 cm). The decimal form is 1.5 inch. Searches for 1 1/2 inches to mm and 1.5 inches to mm use this conversion.

  • How many mm is 1.5 inches?

    1.5 inches is the same as 1 1/2 inches: 38.1 mm exactly. 38 mm is 0.1 mm smaller; 40 mm is 1.9 mm larger.

  • Is 1 1/2 inch pipe 38.1 mm outside?

    No. 1 1/2 inches as a length is 38.1 mm. A nominal 1-1/2 inch pipe (NPS) is a trade size: its outside diameter is 1.900 in (48.26 mm), not 38.1 mm. Inside diameter is smaller still and depends on wall schedule.

  • 1 1/2 inch to mm on a ruler

    38.1 mm sits just past the 38 mm mark on a millimeter ruler (38 mm is 0.1 mm short). A 1-1/2 inch wrench opening is the same 38.1 mm; a 38 mm wrench is 0.1 mm smaller.

  • Is a 2×4 actually 1 1/2 inches thick?

    Yes, when it is dry dressed. PS 20 sets a dry 2×4 at 1 1/2 in by 3 1/2 in, which is 38.1 mm by 88.9 mm. The “2” and “4” are nominal. Green dressed nominal 2 in stock is 1 9/16 in (39.6875 mm).

  • What metric drill is closest to 1 1/2 inch?

    38 mm is 0.1 mm smaller than 38.1 mm, and 40 mm is 1.9 mm larger. A 38 mm hole will not clear a full 1 1/2 in shank. The nearest fractional drills are 1 7/16 in (36.5125 mm, 1.5875 mm smaller) and 1 9/16 in (39.6875 mm, 1.5875 mm larger).

  • What metric bolt is closest to 1 1/2 inch?

    No ISO bolt has a 38.1 mm major diameter. M39, a second-choice size, is 39 mm (0.9 mm larger). The nearest first-choice sizes are M36 at 36 mm (2.1 mm smaller) and M42 at 42 mm (3.9 mm larger).

  • Will a 1 1/2 inch dowel fit inside 1 1/2 inch pipe?

    Inside Schedule 40 NPS 1-1/2 pipe, the nominal inside diameter is 1.610 in (40.894 mm), 2.794 mm larger than 38.1 mm, so a 1 1/2 in dowel passes on the nominal size. Schedule 80 nominal inside diameter is 1.500 in (38.1 mm), the same as the dowel, which is not clearance. The outside of the pipe is 1.900 in (48.26 mm) either way.