2 1/2 inches to mm

Decimal: 2.5 inches

2 1/2 inches (2.5 inches) = 63.5 mm exactly (6.35 cm). The international inch is 25.4 mm, so multiply the inch value by 25.4.

Millimeters
63.5
Decimal inches
2.5000
Nearest 1/64
2 1/2 in (exact on 1/64)

The inches fraction result is rounded to the nearest 1/64 fraction.

2 1/2 inches to mm conversion

2 1/2 inches (2.5 inches) × 25.4 = 63.5 mm. Reverse: 63.5 ÷ 25.4 = 2.5 in.

2 1/2 inches to mm calculator

Use the converter at the top. Type a decimal or a fraction (1/16, 3 1/2). Millimeters update from the same engine as the inch to mm hub (1 in = 25.4 mm).

How to convert 2 1/2 inches to mm

  1. Write the length as a decimal inch if needed: 2 1/2 in = 2.5 in (2.5 inches).
  2. Multiply by 25.4: 2.5 × 25.4 = 63.5 mm.
  3. Optional centimeters: divide millimeters by 10 → 6.35 cm.

Nearest metric size

63.5 mm sits halfway between 63 mm and 64 mm (0.5 mm from each).

64 mm is 0.5 mm larger than 63.5 mm and 65 mm is 1.5 mm larger — the metric sizes usually compared with a 2 1/2 in (2.5 in) cut, hole, or tool. A nominal “2 1/2 inch pipe” is a trade size whose outside diameter is not 2.5 in, so use 63.5 mm only when the length itself is 2 1/2 inches.

2 1/2 inches is 63.5 mm, not a whole millimeter. Whole-millimeter neighbors:

  • 63 mm is 0.5 mm smaller than 2 1/2 inches.
  • 64 mm is 0.5 mm larger than 2 1/2 inches.

Pipe, lumber, bolts, and drill bits

2 1/2 inches as a length is 63.5 mm (2.5 × 25.4). A nominal “2 1/2 inch pipe” is not that diameter. ASME B36.10M NPS 2-1/2 (also called DN 65) has an outside diameter of 2.875 in, 73.025 mm. Published metric charts often round that OD to 73.02 mm. DN 65 does not mean the pipe is 65 mm across.

Schedule 40 wall is 0.203 in, so the nominal inside diameter is 2.875 − 2 × 0.203 = 2.469 in (62.7126 mm). That is 0.7874 mm smaller than 63.5 mm, so a full 2 1/2 in dowel does not pass through Schedule 40 NPS 2-1/2 pipe. Schedule 80 wall is 0.276 in; the nominal inside diameter is 2.323 in (59.0042 mm), 4.4958 mm smaller than the length. Mill tolerance can change the real wall.

ASTM B88 copper water tube labeled 2-1/2 in has an outside diameter of 2.625 in (66.675 mm) for Types K, L, and M — 1/8 in (3.175 mm) larger than a 2 1/2 in length, and still smaller than the steel-pipe OD. Inside diameter depends on the type.

Compared with this length

Difference is from 63.5 mm. Positive means larger than a 2 1/2 in length. 63.5 mm is exactly halfway between 63 mm and 64 mm.

ItemActual sizemmDifference (mm)
2 1/2 in length, cut, or wrench opening2.500 in63.50
NPS 2-1/2 pipe, outside diameter2.875 in73.025+9.525
NPS 2-1/2 Schedule 40, nominal inside2.469 in62.7126-0.7874
NPS 2-1/2 Schedule 80, nominal inside2.323 in59.0042-4.4958
Copper tube, nominal 2-1/2, outside2.625 in66.675+3.175
63 mm drill63 mm63-0.5
64 mm drill64 mm64+0.5
2 7/16 in drill2.4375 in61.9125-1.5875
2 9/16 in drill2.5625 in65.0875+1.5875
M56 bolt, major diameter (preferred)56 mm56-7.5
M60 bolt, major diameter (second choice)60 mm60-3.5
M64 bolt, major diameter (preferred)64 mm64+0.5

Dry dressed softwood that is actually 2 1/2 in thick

Nominal 3 in softwood dresses to 2 1/2 in when it is surfaced dry. A 3×4 is 2 1/2 in by 3 1/2 in (63.5 mm by 88.9 mm). Green dressed nominal 3 in stock is 2 9/16 in (65.0875 mm; PS 20 lists 65.1 mm).

NominalDry dressedmm
3×42 1/2 × 3 1/2 in63.5 × 88.9
3×62 1/2 × 5 1/2 in63.5 × 139.7
3×82 1/2 × 7 1/4 in63.5 × 184.15
3×102 1/2 × 9 1/4 in63.5 × 234.95
3×122 1/2 × 11 1/4 in63.5 × 285.75

Dry dressed sizes are minimums from the American Softwood Lumber Standard (PS 20) at 19% moisture content or less. Inch sizes are the standard of record. Millimeters are those inches × 25.4. PS 20 rounds a few metric equivalents: 7 1/4 in is listed as 184.2 mm (exact 184.15), 9 1/4 in as 235.0 mm (exact 234.95), and 11 1/4 in as 285.8 mm (exact 285.75). Green lumber is larger, and rough lumber is larger still.

63 mm is 0.5 mm smaller than 63.5 mm and 64 mm is 0.5 mm larger, so neither whole millimeter matches a 2 1/2 in shank or wrench opening. A 63 mm hole will not pass a full 63.5 mm pin. M64, a first-choice diameter, is 64 mm (0.5 mm larger). M60 is a second-choice diameter at 60 mm (3.5 mm smaller). M56, the next smaller first-choice size, is 56 mm (7.5 mm smaller). Major diameter is the thread size, not the wrench size.

The same kind of name mix-up at the other focus size is on 1 1/2 inches to mm. Both sizes are linked from the Length Tools home page.

Pipe OD and schedule walls: ASME B36.10M (Schedule 40 wall 0.203 in, Schedule 80 wall 0.276 in). Copper OD: ASTM B88. Lumber: PS 20 Table 3 dry dressed minimums. Bolt diameters: ISO metric nominal major diameter.

2–3 inch chart (1/16 steps)

Sixteenth-inch steps from the same 1 in = 25.4 mm factor. Linked rows have their own pages. The full fraction table is on inch to mm.

InchesDecimalMillimeters
2 in250.8 mm
2 1/16 in2.062552.3875 mm
2 1/8 in2.12553.975 mm
2 3/16 in2.187555.5625 mm
2 1/4 in2.2557.15 mm
2 5/16 in2.312558.7375 mm
2 3/8 in2.37560.325 mm
2 7/16 in2.437561.9125 mm
2 1/2 in2.563.5 mm
2 9/16 in2.562565.0875 mm
2 5/8 in2.62566.675 mm
2 11/16 in2.687568.2625 mm
2 3/4 in2.7569.85 mm
2 13/16 in2.812571.4375 mm
2 7/8 in2.87573.025 mm
2 15/16 in2.937574.6125 mm
3 in376.2 mm

Other inch fractions to mm

FAQ

  • How many mm is 2 1/2 inches?

    2 1/2 inches is 63.5 mm exactly. 2.5 × 25.4 = 63.5. 64 mm is 0.5 mm larger and 65 mm is 1.5 mm larger.

  • What is 2 1/2 inches in mm?

    2 1/2 inches in mm is 63.5 mm (6.35 cm). The decimal form is 2.5 inches. Searches for 2 1/2 inches to mm and 2.5 inches to mm use this conversion.

  • How many mm is 2.5 inches?

    2.5 inches is the same as 2 1/2 inches: 63.5 mm exactly. 63 mm and 64 mm are each 0.5 mm away; 65 mm is 1.5 mm larger.

  • Is 2 1/2 inch pipe 63.5 mm outside?

    No. 2 1/2 inches as a length is 63.5 mm. NPS 2-1/2 pipe outside diameter is 2.875 in (73.025 mm). Schedule 40 nominal inside diameter is 2.469 in (62.7126 mm), which is 0.7874 mm smaller than 63.5 mm, so it is not a 2 1/2 in bore either.

  • Is a 3×4 actually 2 1/2 inches thick?

    Yes, when it is dry dressed. PS 20 sets nominal 3 in thickness to 2 1/2 in (63.5 mm). A dry 3×4 is 2 1/2 in by 3 1/2 in, 63.5 mm by 88.9 mm. Green dressed nominal 3 in stock is 2 9/16 in (65.0875 mm).

  • What metric size is closest to 2 1/2 inches?

    63.5 mm sits halfway between 63 mm and 64 mm (0.5 mm from each). M64’s major diameter is 64 mm, 0.5 mm larger than 2 1/2 in. M60, a second-choice size, is 60 mm (3.5 mm smaller). A 63 mm hole will not pass a full 63.5 mm shank. The nearest fractional drills are 2 7/16 in (61.9125 mm) and 2 9/16 in (65.0875 mm), each 1.5875 mm away.

  • Is 2.5 inches the same as 2 1/2 inches?

    Yes. 2.5 × 25.4 = 63.5 mm exactly. 65 mm is 1.5 mm larger. A nominal 2-1/2 in pipe is a different size: 2.875 in outside (73.025 mm).